Brake pads Akebono or Carbotech
Factory brake pads really are better but that's like the one part they seem to gouge the price on the worst, I usually try to get the closest thing to factory the aftermarket offers, you can usually get Akebono which might actually be the same as factory for quite a bit less on like Tire Rack or sometimes the local parts place will have them.
Spend the money on the Akebono pads.\n\nI\u2019ve been around Napa an Carquest for my entire adult life and even the best from those brands DO NOT compare to the Akebono pads. You can get them from any parts retailer
Change out the pads for ceramic pads like Akebono, they should be quieter and less brake dust.
Duralast gold is good but akebono is likely the OEM manufacturer. If you can find it, get it
Akebono ceramic is the best you can get for stock applications. Very low dust and made in usa. my LX gets Akebono pro act pads.
Pads look good but the rotors look like they have fine grooves in them. For a Honda I’d use centric rotors & akebono pads. You can’t go wrong with that combo.
First those rotors are torched. Get some new rotors. They ain't that expensive for the Corolla. Then get yourself some new pads, Akebono Pro Act. Grab some Powerstop ceramic break grease. Some Ac/Delco silicone brake lube. These 2 products are top notch. Forget permatex, mission, 3m, superlube all that bullshit. If your calipers aren't toasted \"ripped piston boots, rusted pistons or seized/ rusty caliper pins. Then get new calipers. The noise you're experiencing could be from not using anything on the back of the pads where the piston touches and the caliper touches. Ripped piston boots give the old screechy screech as well. Take that caliper bracket off the wheel and wire wheel it free of all dirt/rust paying particular attention to where the pad clips sit, you want those areas to be perfectly clean and square. Razzle it down with some brake clean then apply the powerstop grease to the pad clip seats then set the clips and install the bracket back onto the wheel. Next use some of that powerstop grease and paint the ears on the new pads so they slide nice and easy in the pad clips. You don't need much. Please don't use copper anti seize on the pad ears. Just the powerstop stuff. Next clean off those caliper pins, boots and bores. Make sure the face of the piston is free of rust and dirt. Get those bores and boots super clean. Then add the ac/delco silicone to the pins careful not to blob any on the tip face of the pin, that is important. The ac delco is a bit different than all silicone paste/ grease. Be careful with it and don't apply too much. Get a little delco in the boot baffles and squish it around to distribute it inside the boot. Then just put it all back together. Bleed the lines in the correct order and done. I promise your brakes won't make a peep for a long long time. Service them at every oil change to make sure everything is lubey loobed.
I used Hi-Q rotors and Akebono pads on my Patrol. Stops great but the Akebono pads cause a lot of brake dust.
im running XP10s... so far this set up is amazing, the braking is strong initial bite with little fade. Just take in consideration that this Carbotech pads are modular which means you will have a slight longer pedal travel than normal. And yes they are super noisy, when i drive it on the street i try to be careful with my braking and not feather the brakes, that will make then literally screech and grind the rotors, instead i try to brake a bit harder than usual to get a good bite and then let go of the brake once i stoped (put the car in neutral most of the time or creep forward little by little to releave some heat).
Don’t recommend Akebono because their ProACT pads are weaker than stock.
Write your review
Help others - share your experience with this part.