NGK Iridium gapped at 0.026 only. They’re great
That is what I am running in this 1996 Corolla and my gas Mileage is better than ever! Made a huge difference in power .
I drive a 01 4runner and I run NGK plugs and wires. Almost 300k on the dash.
No issues with Bosch red coils from Shopdap Bosch Red R8 Ignition Coil for VW Audi 06E905115F - Deutsche Auto Parts (shopdap.com) Spark plugs: NGK Ruthenium HX, #92400.
Got some NGK Ruthenium HX plugs at NAPA this morning. Miss is gone, car runs perfectly again. Plus they're cheaper and supposedly will last longer than the platinums.
Thought I would follow up on this discussion. Ordered the NGK LFER7BHX Ruthenium HX. The priority package showed up after some challenges with the local Postal Service. As advised, on Tuesday took the car for a short drive to warm it up then started the task. Was a little pensive taking the engine cover off. To anyone who has never done it on that particular car, just pull each corner straight up about an inch and it comes right off. The cover is held on with posts that fit into rubber grommets so the chance of breaking anything is almost zero. Found a very old 10-14mm open end from the tool kit from a long gone motorcycle in the junk drawer, A few minutes with the belt grinder and a "perfect width for the ground bolt" 10mm open end was discovered hidden inside. The only real challenge is disconnecting the wiring loom from the coil packs. Several iterations of 'watch a video, give it a try, watch a different video, give it a try ...' ensued but I was finally able to get them disconnected. Gently removed the coil packs and one-by-one removed the plug, installed a new one, torque to 30Nm, wash-rinse-repeat. Put a little dielectric grease into the plug boot of the coil pack and the coil pack\\wiring loom connector, a little SYL-Glyde Silicone Grease on the large coil pack to engine seal and reinstalled the coil packs. Torqued the ground bolts to 12Nm, then put on the ground strap and torqued the nut to 12Nm while holding the bolt steady with the afore mentioned "super wrench". Fought with the wiring loom to get it back on all the coil packs, popped the engine cover back on and Bob's you uncle. Drive to the dealer Wednesday morning and went in to talk to the Service Writer. Mentioned that they did not have to rotate the tires (had already put the X-Ice tires on two weeks earlier) nor change the plugs as I had done that the day before. He gave me a strange look and said "Yes, VW recommends they be changed but with only 15,000 miles on the car I would not have bothered". Doh!!! Primary lesson learned here is "Call and schedule service yourself rather than let your wife do it." That way you can challenge the items on the "what will you be doing at this service" before spending an afternoon under the hood. (Side note, it is 'her' car as 'my' car is the FRS, hence her desire to schedule the maintenance.) They did the usual "full inspection" on the car and came back with "the rear brake pads are down to 3mm and should be replaced". They had photos to "prove" the pads were down to 3mm. I though this was strange and will be starting another thread to go over that discussion with the Service Writer.
I use NGK Iridium. They seem to burn a little cleaner than some other plugs I’ve used in the past.
For a stock 4.3 you won’t see any performance difference regardless of what you put in there. Cheap copper plugs will work great but your going to be replacing them every 25-30,000 miles, iridium will probably last as long as the rest of the vehicle.
I've had my 2006 Audi a3 3.2 quattro dsg for 5 years now, and every year or so I will have an issue with a misfire on cylinder 6. It is always cylinder 6. I use the recommended NKG IZKR7B(7563) plugs. I often find that the cylinder 6 plug has a crack on the ceramic insulator around the electrode. On one of the plugs, half of the insulator is missing. Replacing the plug always fixes the misfire. I also noticed most recently when I removed the damaged plug, it was very hard to turn and some of the aluminum from the head has fused to the threads, leading me to believe that the cylinder is getting too hot.
I also just put in a set of NGK BKR7E's and gapped them a little large (.034) seeing as the ones I pulled out were at .043 That did nothing and the issue is still persistent.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads NIPPARTS got the first review!
The brake pads APP got the first review!
The drive shaft OEM BMW got the first review!
For wiper blades PIAA already 100 reviews.
For tires OEM Toyota already 25 reviews.
In the rating best ignition coil already 13 brands participate!
In the rating best water pump already 12 brands participate!
In the rating best air filter already 5 brands participate!
In the auto rating battery for Volkswagen Golf already 5 brands participate!
In the auto rating tires for Toyota Corolla already 50 brands participate!
In the auto rating oil filter for Volkswagen Passat already 5 brands participate!
For starter motor OEM Volkswagen already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
