Brake pads Bosch or Duralast
I've been doing my own brake job for a while and have used Bosch QuietCast rotors and Bosch QuietCast Premium Disc brake pads, both purchased from Amazon. No complaints.
Just replaced all four brake pads and rotors on my 2018 MZ3 hatch with 46,000 miles. Used Bosch quiet cast brake pads and rotors. Paid around $350 for parts and took me around three hours.
I just put Duralast Elite Ceramic pads and Duralast Gold rotors on my 2017 5.0 and have been very pleased with them. While not physically measured I’m of the opinion stopping distance has been reduced. Everything you need is in the box and rotors are coated to resist corrosion and have no film to remove before installation.
I change brakes at least yearly, sometimes more often if I'm driving in mountainous areas alot. I always buy the Bosch ceramic brakes and just buy the low cost rotors because I change them at every brake change (cheaper than having them turned in Phoenix). I buy everything off Amazon. A four wheel brake job will cost me less and $100. 2019 LE.
I've been using the Bosch QuietCast ceramic brakes in the past and have zero complaints so I think I'll go with these: BOSCH BC1212 QuietCast; Ceramic - Rear ($26.79) BOSCH BC2076 QuietCast; Ceramic - Front ($37.79) I'm looking for high quality/high value. I don't need "high performance", I'm not doing any track stuff, just basic commuting but would like longevity, value, performance, etc. I ended up getting: POWER STOP JBR1763SCR (Daily Driver) Semi-Coated - Front BOSCH BC2076 (Premium) QuietCast; Ceramic POWER STOP JBR1764SCR (Daily Driver) Semi-Coated - Rear BOSCH BC1212 (Premium) QuietCast; Ceramic It was around 260 dollars with tax and shipping.
Did all brakes and rotors with top duralast gold and heavy duty ceramic pads- maybe 600
Duralast Friction Ceramic Brake Pads D1766 front 49.99 back 39.99 old pad and a harbor frieght C clamp 8.99 98.27 guesstimation on sales tax 104.97 total/
I own a 91’ fj80 land cruiser. I have limited options for OEM stuff these days due to the truck being 30+ years old. I’ve got a CSF radiator in mine because having my OE unit re-cored was $1000+ and the csf was ~450. Toyota new stock, unavailable. I use 555 rod ends and sumo brand rebuild kits, koyo bearings. OE suppliers for toyota without the dealer markup. They’re quick to get here and prices are competitive (i got a guy). As long as its pretty competitive and a known brand, i’ll gladly put aftermarket stuff in my toyota as long as it is of good quality. Rock auto has aisin and denso stuff for these trucks regularly. Been putting bosch brake pads on it since i got it, no issues there.
I went for Bosch models. Fronts have faired much better than oem. Rears I had some other issues (didn’t use service mode) that destroyed them prematurely
For my (owned 3 years, purchased used) 2014 Honda Crosstour I've always had to grind down the edges of the pad mounting plate tabs on Bosch brakes a couple of mm to get it to fit into the calipers. I have just received a new set, and while I still had to grind down the edges to get them to slide into the calipers, the top and bottom edges were MUCH shorter than the previous pads. So much so that when braking after reversing direction, the pads will shift in the calipers with a noticeable 'click' as the brake pads engage the disks to slow the car and are thus moved to the other end of the caliper. The overlap between the brake pad plate and the 'C' in the caliper where the tab meets the caliper is only 2mm or so. Definitely less than I am comfortable with.
Write your review
Help others - share your experience with this part.