Brake pads Bosch or OEM KIA
It’s got 102,700kms on the clock and owned it since new. I’m still on my first set of brake pads.
So far I've been happy with Bosch brake pads.
Bosch Quietcast pads. They have good stopping power, are quiet (so far) and have low dust, so they are great for my daily driver.
I used rockauto and got.
BOSCH BC433 ceramic Brake Pads on my front brakes.
They have been real good.
I also have those Bosch pads on my Tundra and they are really good, quiet, low dust, excellent overall.
I think the Bosch pads work fine.
Last year a shop replaced the rear brake pads and disks but since then handbrake never was like before. They kept telling me it will get better which I believed at the time but it never did. Last month I've passed inspection and they told me that the rear left handbrake was almost out of spec and I'd need to check it out although it passed.
So a month later I've bought a Bosch kit, sliders, pads, grease, toolkit etc and replaced the 1 year old ferodo pads. Now handbrake is like it should be and I'm happy with it but take a look at the old pads...
Both inner side alignment pins (caliper side) are bent.
Last month I've passed inspection and they told me that the rear left handbrake was almost out of spec and I'd need to check it out although it passed. So a month later I've bought a Bosch kit, sliders, pads, grease, toolkit etc and replaced the 1 year old ferodo pads. Now handbrake is like it should be and I'm happy with it but take a look at the old pads...Both inner side alignment pins (caliper side) are bent.
I replaced front pads and rotors on my Tiguan, and afterwards, when going between D <-> R and applying the brakes, the first brake application causes a "clack" on both sides at the front. Pads are Bosch 1633A. spring clips (integral to pads) are seated properly. Pads and rotors were bedded properly. Wheel lug bolts torqued properly. I have the official instructions from VW. I've probably done ~20 brake jobs in my life, mostly Volvos (over half of those were sliding-caliper designs like the Tiguan's). What I tried (with no success): searching and searching and searching forums, only found 2 other people with a similar issue on FCP's Brake Replacement YouTube video measured and compared all latereral dimensions of the pad's plate between new and old, same dimensions re-installed the pads all bolts are torqued properly (caliper carrier 200 Nm; caliper pin bolts 35 Nm) found a Tech Bulletin from VW that mentions there are inner- and outer-specific orientation for the pads. This appears to apply only to the Genuine (labeled TRW) pads, as all 3 Bosch pads are identical in every way that I can discern bought a set of Genuine VW pads (labeled VW), ensured the correct orientation of pads according to the Tech Bulletin, and they still clack. pad backing plate dimensions are the same as the Bosch. Ack! More money! bought a set of genuine caliper carriers (with the thinking that perhaps when I wire-wheeled the old caliper carriers to remove rust, it took off too much material). I didn't install them because I measured all the dimensions that interface with the pads and the new are identical to the old.
Am cumparat pentru un Audi A3 8P placute si discuri noi pe față de la Bosch. Placutele sunt acelasi model utilizat si inainte de schimb. Nu am mers prea mult cu masina de cand le-am schimbat dar am depasit 500-600 km. Acum ca s-a facut cald dupa 10-15 minute de mers in oras- cand se incing incep sa scartaie consistent la orice tip de franare- lenta, brusca. Au inceput sa fara asa din primele zile de utilizare. Nu e vorba de vreo depunere pe suprafete. Oricum problema apare dupa ce sunt folosite in oras 10-15 minute.
Write your review
Help others - share your experience with this part.