Ive been running the ferodo DS2500 and it seems to work well for occasional track use and mixed daily as well. Not too noisy on my older 911.
carbotech xp10/xp8(f/r), not a daily but the car sees plenty of street miles. they are noisy and dusty but this setup has been perfectly fine for me.
Right now I use Ferodo DS 3.12 on RE71RS tires. They are pretty high bite and take some getting used to. I might go a rung lower on the friction scale and go with DS 1.11 next time because of that. But the DS 3.12 are unfadeable and very consistent.
I’ve used carbotech XP10 for years because it’s the only pad that has never had any of these kinds of problems. Also also swapped between 1521 and XP10 seamlessly. The only time I had a problem like this was when I used some very cheap rotors that couldn’t handle the track abuse, you could actually see the rotor surface getting pitted. Yours look fine by comparison.
For my GR86 Carbotech XP10s have been amazing on the track, seriously no complaints at all. The XP10s with Castrol SRF have been a great combo and held up really well even on some really big/high speed tracks. I swap in my OEM pads when I’m not tracking the car for awhile. It’s not great because I have to bed the pads every time I change them. Once I’m through the OEM pads I’m going to get the Carbotech 1521’s for the street, that way like you mentioned I think I can avoid having to avoid bedding my brakes with every change. The XP10’s function well on the street but they feel a little rough if not up to temp and they are insanely loud.
I personally use Carbotech XP10 for track and Stoptech Sport pads for street on the same rotors
Ferodo DS2500 are a great compromise pad. They’re a bit more on the race side of things but I never had issues with them being sketchy. Just get a bit of heat into them early to make sure they’re there.
Recently completed my HPDE and by the end of the day my stock pads were completely gone. Got my front rotors and all my pads replaced soon after that. I went for the Ferodo DS2500 pads. While bedding my pads, I noticed the brake feeling/bite is quite nice when braking at around 50-60% pressure, but once I tried emulating track style braking (i.e hitting brake pedal very hard) I noticed that my brake pedal was vibrating/rattling and also felt some sort of scraping was going on. This would happen even when hitting brakes hard from low speeds of ~30 mph. It's felt entirely on the front brakes. ABS did not engage, so I don't think the vibrations are from that. The obvious visible difference I see is the use of high temp brake lube from the shop.
Ferodo Ds2500 as brake pads or Ebc Yellostuff (a tad cheaper). Avoid drilled or grooved rotors because kinda useless. Just a good oem equivalent like Brembo (if in you market have CTF go for it)
My rear pads cracked after 3 months, 4k km of use.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads OEM Alfa Romeo got the first review!
The brake caliper OEM BMW got the first review!
The brake pads OEM Infiniti got the first review!
For wiper blades PIAA already 100 reviews.
For battery Energizer already 25 reviews.
In the rating best water pump already 12 brands participate!
In the rating best timing belt already 13 brands participate!
In the rating best head gasket already 3 brands participate!
In the auto rating oil filter for Volkswagen Passat already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating tires for Subaru Outback already 50 brands participate!
For cabin filter Fram already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
