I just installed Galfer HH sintered pads and they’ve been solid so far. Definitely an improvement from stock but they were getting pretty worn down
I really liked Project Mu Club Racers as a "streetable-ish" track pad. They were fairly tolerable on the street as long as they were bedded in. They occasionally squeal when coming to a stop once below 15mph.
Higher-temp and higher-mu pads (Project Mu HC+R3) + braided brake lines + DOT 4 fluid for me. Slotted fronts, blank rears.
I order the Galfer e-bike brake pads G1652 from Amazon and they fit really well. Definitely would recommend
Red stuff are absolutely NOT track worthy. Will fade in like 1 lap. Any pads advertised as "low dust" tend to fade pretty fast. Yellow might be ok but I think they're still more of a performance street pad. Project MU HC+ are a good streetable track pad, maybe the best, use them on my Megane RS, no trouble with 20 mins sessions on high speed tracks and trackday tyres (Yokohama AD09). A little squeel at low speed on track but quiet enough to live with IMO.
Project MU HC+ pads. These have a higher operating temp range than Ferodo DS2500 and are perfectly streetable too. I get very minor squeal when coming to a stop if it's been a while since they were used hard. they also have great braking feel IMO, nice and sharp, and perfectly controllable. I use them on a Renault Megane RS 280 Cup, I've used them on track with semi-slicks (AD09s) and they held up great in 15 min sessions. Some minor vibration after the day but that fades away with use (or another hard besdding session). Do not recommend Ferodo DS2500 especially with semi slicks. Might be ok for your first day if you're slow, but you'll almost certainly cook them on your second and get deposits on your rotors. Great performance pads or the street though. On my car I only use them on the front, rears are stock.
I did Project MU B force pads. DBA 4000 rotors, Stop tech stainless steel brake lines, Motul 660 brake fluid, radium brake booster brace(a must). Make sure to set those pads in the correct sequence and they gonna rip your face off bud! I had 6 piston brembos also, what a difference!
I do not recommend these for the street, however the track performance is off the charts.
PMU HC800+ was my dual duty pad and was a solid compromise. But end of the day it’s just that - a compromise
I just switched from OEM (Brembo HH Sintered, I think) pads to Galfer HH Sintered pads. I forgot to scotchbrite the discs and I think I glazed everything up during bedding-in process. I used scotchbrite like mad on the discs and sanded the pads with 220 grit until they were dull like when new, but the brakes seem to have the same behavior - heavy brakes test after 10 mile bed-in ride, the brakes plateau without getting to ABS trigger unless I squeeze like a motherfucker. The previous pads I could stand up on the front wheel with one or two fingers, so I feel like I've done something wrong.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads NIPPARTS got the first review!
The brake discs Hella got the first review!
The brake discs OEM Suzuki got the first review!
For tires OEM Toyota already 25 reviews.
For tires IRONMAN already 25 reviews.
For starter motor OEM Volkswagen already 25 reviews.
In the rating best ignition coil already 13 brands participate!
In the rating best fuel pump already 5 brands participate!
In the rating best turbocharger already 4 brands participate!
In the auto rating headlights for Volkswagen Golf already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating brake pads for BMW M2 already 5 brands participate!
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
