You don't need a torque wrench, NGK plugs have a crush washer and specify half turn past initial contact. Did my Mazda 3 with no issues. I have a torque wrench and didn't use it.
Harbor Freight has the torque wrench you’d need for $19.99 the Pittsburgh 3/8" drive and a 3/8" drive extension set for $16.99. I’d also grab a magnetic spark plug socket from AutoZone for $14.99 (just go straight for the magnetic one, it makes life way easier).
For the spark plugs themselves, I’d stick with NGK, but make sure it’s the correct spec for your car, since they make different cx5's, some being NA and some being turbo.
As for the "paste," some people put antiseize or dielectric grease on the threads to make future removal easier. I personally skip it because I want zero chance of anything getting into the engine, plus grease can amplify the torque applied with the wrench, which is bad. I’m hoping this is what you mean by paste?
If you do it yourself, the first time costs roughly $100-120 for the tools, and still is about half of what the dealer is quoting. After that, you just pay for the spark plugs themselves for future changes, which brings the cost down to around $50-70 per change since now you'll have the tools.
Get an icon click type torque wrench from harbor freight when they have a sale. And a deep socket set for spark plugs plus dont buy your plugs on Amazon. Go to rockauto. And buy them there buy ngks also rediitt has a rockauto sub and usually people give out 5%off coupons. Also Do not use cheap aftermarket plugs on your car also you'll need a regular ratcheting wrench and extension. Never use torque wrench to loosen plugs it csn destroy the calibration
NGK Laser Iridiums will last longer, but those aren't bad per se.
I had to put a new spark plug in mine after only a few hours of use. It had some China branded in it and I switched to NGK. Also propane creates a hard harder to jump spark gap so you generally have to narrow the gap a tiny bit from typical specs when you’re going to run propane. Since I only run propane I went down a little on the gap and it runs flawlessly. I optimize the gap width by seeing which widths responded best to a sudden surge load without hesitating.
NGK Lazer Iridium Plugs is what I got to replace them in my car. I believe those are what Mazda OEM plugs are, but it’s just cheaper to buy the NGKs from a part store.
use NGK spark plugs, the best ones are the PFR6Q
Went with NGK spark plugs that was bundled with some generic wires and coils, not ideal but it’s all I could afford at the moment
I learned that proper, very hard to tell, NGK knock offs even existed after I was bitten by fake ones off Amazon. The porcelain around the center electrode broke off and went through the engine.
I have installed brand new NGK sparkplugs and Bosh ignition coils...but the cylinder 1 misfire does not move or is resolved at all.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads OEM Alfa Romeo got the first review!
The tires OEM Fiat got the first review!
The ABS unit OEM FORD got the first review!
For oil additives LIQUI MOLY already 25 reviews.
For tires GISLAVED already 25 reviews.
In the rating best cabin filter already 13 brands participate!
In the rating best shock absorbers already 13 brands participate!
In the rating best fuel pump already 5 brands participate!
In the auto rating shock absorbers for Ford Ranger already 20 brands participate!
In the auto rating headlights for Volkswagen Golf already 5 brands participate!
In the auto rating tires for Toyota Corolla already 50 brands participate!
For cabin filter Fram already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
