Brake discs POWER STOP or OEM Volkswagen
I run PowerStop crossdrilled/slotted anti rust on my Infiniti and my truck. I've used them for a few years and like the braking on them. Have had no issues over 30000 combined miles with the heavy load on the truck and spirited drive of my car. I've also installed the PowerStop OEM grade pads and rotors on some friends cars and they have been very pleased. I also use the PowerStop pads with these setups.
FWIW, I recently replaced my front rotors and pads at 40k and I have about 8mm on the back. At this rate, I'll probably have to replace the backs around the same time I do the fronts again. My rotors look nothing like yours though. Mine are smooth and no grooves.
I had the impression that those discs wouldn’t warp as easy as one piece discs but it looks as I was wrong. VW tried to machine my warped discs with them mounted on the car at one point but they failed so badly that they did not even want to show me the result. After that they messured the runout on new discs on the bench and found them OK. After the discs were mounted on the hubs they were messured again and that one of them had warped. That was the way they found the bad hub. I was quite surprised when I was told that VW did not have any tolerances for the runout on the hubs or the discs. I took for granted that they had quite strict tolerances both on the hubs and the discs. I don’t know if the eight piston caliper and the setup with opposed pistons makes the whole system more sensitive to warpage or not but that has been suggested. And to get this a bit more connected to the thread subject I can add that I have not found any alternative to VW original 365 mm floating discs at all. I was quite surprised to find them cheaper than the one piece 334 mm discs to my Passat W8 though.
Could be the hubs. Mine had an axial throw of 0,02-0,03 mm which I thought wouldn’t affect the discs. I filed a complainment to VW regarding warped discs and they blamed the calipers. Told me one of eight pistons was a bit sluggish. With new calipers and two sets of discs later they found what I had meassured before the complainment, a warped hub. The last pair have not warped after the typical 5000 km mark as before. So at least the floating 365 mm discs are very sensitive regarding straight hubs.
Just the bigger carrier with the bigger rotors on the front. Didn't bother with bigger for the rears. I bought Red Stuff pads.
That being said, it would be great to see a basic writeup with pics of the fronts and rears being changed. I ordered and received some new slotted/drilled rotors with ceramic pads. When ordering, I just used the GTI as the model, since it uses the same brake rotors as the TDI, 312mm F, 272mm R - IIRC. If I have time, I will get some pics and write a rudimentary writeup on it. Not sure if I have time/patience to tackle this myself so I may just have my Audi/VW guy do the work (he has many more tools and 2 lifts). In any case, I will try to get some info and pics in here.
Just discussed this last week. I side with my VW dealer on it. They recommend just replacing the rotors, its really not that much more than having them turned, considering you almost guarantee no pulsation, no shimmy or shudder and more even brake wear.
Engine braking is how I got 60k miles out of the original brake rotors and pads on my '07 GTI as well as a steady 30 mpg while barely trying.
I am happy with the R32 setup so far ( rotors are freaking heavy); but if I was to upgrade it would be either AP or stoptech trophies....
The cause is Sub-Standard, Cheap "Made in China" Rotors.
Write your review
Help others - share your experience with this part.
Brake discs Zimmermann or POWER STOP
Brake discs Brembo or Zimmermann
Brake discs Brembo or POWER STOP
Brake discs Zimmermann or Centric
Brake discs Zimmermann or STOPTECH
Brake discs Zimmermann or OEM Volkswagen
Brake discs Zimmermann or EBC
Brake discs Zimmermann or Raybestos
Show all