Brake pads Bosch or Ferodo
Ive been running the ferodo DS2500 and it seems to work well for occasional track use and mixed daily as well. Not too noisy on my older 911.
Right now I use Ferodo DS 3.12 on RE71RS tires. They are pretty high bite and take some getting used to. I might go a rung lower on the friction scale and go with DS 1.11 next time because of that. But the DS 3.12 are unfadeable and very consistent.
Bosch quiet cast or Zimmerman. Also Bosch blue pads, ceramic if you want clean and semi metallic if you want to stop
bosch quiet cast pads and rotors. changed my life
I purchased some DBA Sport Rotors from Australia which came with, I'm pretty sure Bosch brake pads which were brilliant!
Ferodo DS2500 are a great compromise pad. They’re a bit more on the race side of things but I never had issues with them being sketchy. Just get a bit of heat into them early to make sure they’re there.
I'm going to tell you ferodo DS 1.11. Street driven on them a ton very easy on rotors. Endurance pad, much better than other things I see mentioned a lot like it blows my mind when people think RSL29s are better. I don't have an M3 but I have a 330ci which has the same brakes, and I've had lots of other cars from Corvettes to Mustangs and camaros. Have run that compound a ton.
I replaced front pads and rotors on my Tiguan, and afterwards, when going between D <-> R and applying the brakes, the first brake application causes a "clack" on both sides at the front. Pads are Bosch 1633A. spring clips (integral to pads) are seated properly. Pads and rotors were bedded properly. Wheel lug bolts torqued properly. I have the official instructions from VW. I've probably done ~20 brake jobs in my life, mostly Volvos (over half of those were sliding-caliper designs like the Tiguan's). What I tried (with no success): searching and searching and searching forums, only found 2 other people with a similar issue on FCP's Brake Replacement YouTube video measured and compared all latereral dimensions of the pad's plate between new and old, same dimensions re-installed the pads all bolts are torqued properly (caliper carrier 200 Nm; caliper pin bolts 35 Nm) found a Tech Bulletin from VW that mentions there are inner- and outer-specific orientation for the pads. This appears to apply only to the Genuine (labeled TRW) pads, as all 3 Bosch pads are identical in every way that I can discern bought a set of Genuine VW pads (labeled VW), ensured the correct orientation of pads according to the Tech Bulletin, and they still clack. pad backing plate dimensions are the same as the Bosch. Ack! More money! bought a set of genuine caliper carriers (with the thinking that perhaps when I wire-wheeled the old caliper carriers to remove rust, it took off too much material). I didn't install them because I measured all the dimensions that interface with the pads and the new are identical to the old.
Just a word of caution, I ordered Bosch pads off of RockAuto and received off brand pads wrapped in shop towels in Bosch boxes. Still put them on and they're alright, but not what I bought. Wasn't worth it to me to send back. Not RockAuto's fault, they have third party suppliers. I'm sure they would have taken care of it had I cared enough
I had a track day today with 1 hour session and closer to the end they were fade.When I took the pads out to check I noticed that they are extremely glazed like covered with a melted metal.Also, looks like they covered rotors with this melted metal, the inner side of both of them.The outer rotors surface is fine. The outer pads look the same glazed.I was checking them yesterday last time and they looked fine.The friction material looked fine and not that glazed.It's on the last photo.I was trying to brake short and strong all the time.There car is Suzuki swift sport.Brake pads ferodo dsuno.Track Zolder.
Write your review
Help others - share your experience with this part.