I bought Dynamic Friction for my wife’s car and have been happy with them.
I have Dynamic Friction 5000 low metallic pads, better bite than ceramics and no brake judder.
Ferodo DS2500 paired with Zimmerman blank rotors and Motul RBF600 is what I use. The tracks I go to are more technical and not fast so it's great for my use case. I imagine if I went to a track where speeds are above 150Km/H and have long, fast corners, I would need better pads. I'm considered intermediate to advanced and last ran a 1:47 at CTMP DDT with worn Vitour Tempesta Enzo tires. I think I can run low 40s this year. I would not track with stock pads. I overheated my pads and brake fade hit hard. The pads melted and I went off the track and almost over the hill at TMP (Cayuga).
I used DS2500 for my first 2 track days but outgrew them rather quickly on a 2800 lb car. Last time I swapped to DS1.11 and felt much more confident braking deeper into corners with zero fade at my intermediate level. Now I just use DS2500 for the street and canyons.
I recently got the dynamic friction rotors and pad kit to replace the oem rears and I like them so far. It’s only been about 500 miles, but in my opinion are a little better at stopping compared to the oem. Plus the price was really good.
Duralast stuff is fine. Their pads are fine. Their pads also have a lifetime warranty through AutoZone.
if you want raw stopping power then Ferodo DS2500's are great.
Recently completed my HPDE and by the end of the day my stock pads were completely gone. Got my front rotors and all my pads replaced soon after that. I went for the Ferodo DS2500 pads. While bedding my pads, I noticed the brake feeling/bite is quite nice when braking at around 50-60% pressure, but once I tried emulating track style braking (i.e hitting brake pedal very hard) I noticed that my brake pedal was vibrating/rattling and also felt some sort of scraping was going on. This would happen even when hitting brakes hard from low speeds of ~30 mph. It's felt entirely on the front brakes. ABS did not engage, so I don't think the vibrations are from that. The obvious visible difference I see is the use of high temp brake lube from the shop.
Ferodo Ds2500 as brake pads or Ebc Yellostuff (a tad cheaper). Avoid drilled or grooved rotors because kinda useless. Just a good oem equivalent like Brembo (if in you market have CTF go for it)
I had a track day today with 1 hour session and closer to the end they were fade.When I took the pads out to check I noticed that they are extremely glazed like covered with a melted metal.Also, looks like they covered rotors with this melted metal, the inner side of both of them.The outer rotors surface is fine. The outer pads look the same glazed.I was checking them yesterday last time and they looked fine.The friction material looked fine and not that glazed.It's on the last photo.I was trying to brake short and strong all the time.There car is Suzuki swift sport.Brake pads ferodo dsuno.Track Zolder.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads NIPPARTS got the first review!
The brake discs Hella got the first review!
The brake discs OEM Suzuki got the first review!
For tires OEM Toyota already 25 reviews.
For tires IRONMAN already 25 reviews.
For starter motor OEM Volkswagen already 25 reviews.
In the rating best ignition coil already 13 brands participate!
In the rating best fuel pump already 5 brands participate!
In the rating best turbocharger already 4 brands participate!
In the auto rating headlights for Volkswagen Golf already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating brake pads for BMW M2 already 5 brands participate!
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
