I think they work just fine. They squealed a bit even after running them in, it stopped however after the first track day where i properly cooked the brakes.
If you want a bit more performance without loosing cold braking, use ferodo ds performance, they're amazing price-quality wise.
I've been running the stock brakes with aftermarket pads for a few years and it's worked well for me. Mintex 1144, Ferodo DS2500 and Roddisons pads have all been great.
Ferodo DS2500 paired with Zimmerman blank rotors and Motul RBF600 is what I use. The tracks I go to are more technical and not fast so it's great for my use case. I imagine if I went to a track where speeds are above 150Km/H and have long, fast corners, I would need better pads. I'm considered intermediate to advanced and last ran a 1:47 at CTMP DDT with worn Vitour Tempesta Enzo tires. I think I can run low 40s this year. I would not track with stock pads. I overheated my pads and brake fade hit hard. The pads melted and I went off the track and almost over the hill at TMP (Cayuga).
I used DS2500 for my first 2 track days but outgrew them rather quickly on a 2800 lb car. Last time I swapped to DS1.11 and felt much more confident braking deeper into corners with zero fade at my intermediate level. Now I just use DS2500 for the street and canyons.
I used Mintex 1144 on my MK7.5 ST. Were great for fast road and some Nurburgring laps in a year.
I’m running DS2500 on my GTI and they are just not *quite* robust enough as I have progressed into the more advanced groups.
I switched to the Ferodo DSUno. I am satisfied with its performance, but they seem to struggle because of something. Today, after the track day on Saturday, I checked it and found a crack and a gnawed edge. Also, they have uneven wear, about 0.5-1mm difference. The differences are between the top and bottom parts of the pads, front and back parts and on different sides of the same rotor (inner and outer pads). Uneven wear was with the old pads as well. Recently, I installed brake air ducts, and after going out from the track, the temperature was, in the worst case, 480C degree, which looks fine for these pads. In total, I drove for about 3 hours on tracks, one on a wet track (so no hard braking) and two moderately/hard(8-9/10) braking. The brake rotors are also new, Zimmermann blank, installed with pads. The initial thickness of the pads is 16.4mm (with the plate, the plate is 5.5mm, so the "pure" pad is about 11mm) Currently, I have eaten about 4.5-5mm of the pads in 3 hours of tracking.
I run the Sebro slotted rotors with Ferodo DS3.12s on track, which are louder than a school bus on the street, so I swap back to OEM pads and rotors after each event.
I swapped out the rear pads on my 2017 Mk7 Golf R following the instructions for doing so with OBD Eleven Pro to a "t" and still wound up with a plethora of error codes. I installed new (Ferrodo) pads
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads OEM Alfa Romeo got the first review!
The brake caliper OEM BMW got the first review!
The brake pads OEM Infiniti got the first review!
For wiper blades PIAA already 100 reviews.
For battery Energizer already 25 reviews.
In the rating best water pump already 12 brands participate!
In the rating best timing belt already 13 brands participate!
In the rating best head gasket already 3 brands participate!
In the auto rating oil filter for Volkswagen Passat already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating tires for Subaru Outback already 50 brands participate!
For cabin filter Fram already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
