if you want raw stopping power then Ferodo DS2500's are great.
I was a huge fan of Ferodo DS2500s on Centric rotors. They performed insanely well for street duty and were decent enough for track days.
I never had an Audi but I have a 2009 VW Jetta that's still running, it's my grocery getter. The breaks have lasted since 2012 as insane as that is, there's still a 3/4th of carbon on the pads. I changed the oil all the time, grew up with a car dad. But if VW's are anything like Audi's just maintain it and it'll run for the next decade.
I put brakes from a 2008 R32 on my MK6 gti. They were cheaper than the golf r on ebay at the time. They work really well.
Ferodo DS2500 is about the best pad you can get.
I've got OE spec ferodo on my 208 GTi no complaints from me, got brembo on my Saab 9-5 aero again all good I would avoid the cheaper end of the market
I switched to the Ferodo DSUno. I am satisfied with its performance, but they seem to struggle because of something. Today, after the track day on Saturday, I checked it and found a crack and a gnawed edge. Also, they have uneven wear, about 0.5-1mm difference. The differences are between the top and bottom parts of the pads, front and back parts and on different sides of the same rotor (inner and outer pads). Uneven wear was with the old pads as well. Recently, I installed brake air ducts, and after going out from the track, the temperature was, in the worst case, 480C degree, which looks fine for these pads. In total, I drove for about 3 hours on tracks, one on a wet track (so no hard braking) and two moderately/hard(8-9/10) braking. The brake rotors are also new, Zimmermann blank, installed with pads. The initial thickness of the pads is 16.4mm (with the plate, the plate is 5.5mm, so the "pure" pad is about 11mm) Currently, I have eaten about 4.5-5mm of the pads in 3 hours of tracking.
Recently completed my HPDE and by the end of the day my stock pads were completely gone. Got my front rotors and all my pads replaced soon after that. I went for the Ferodo DS2500 pads. While bedding my pads, I noticed the brake feeling/bite is quite nice when braking at around 50-60% pressure, but once I tried emulating track style braking (i.e hitting brake pedal very hard) I noticed that my brake pedal was vibrating/rattling and also felt some sort of scraping was going on. This would happen even when hitting brakes hard from low speeds of ~30 mph. It's felt entirely on the front brakes. ABS did not engage, so I don't think the vibrations are from that. The obvious visible difference I see is the use of high temp brake lube from the shop.
Same on my wife's '22 Atlas. So much so that I think it activates the parking sensors on every occasion when we slowly come to a stop, like in a red light and nothing is around the vehicle to make the parking sensors activate. It's just at 37k miles but I'm considering upgrading the pads and rotors!
I had to replace my brakes early as well, and I was also past the extended warranty campaign.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads OEM Alfa Romeo got the first review!
The brake caliper OEM BMW got the first review!
The brake pads OEM Infiniti got the first review!
For wiper blades PIAA already 100 reviews.
For battery Energizer already 25 reviews.
In the rating best water pump already 12 brands participate!
In the rating best timing belt already 13 brands participate!
In the rating best head gasket already 3 brands participate!
In the auto rating oil filter for Volkswagen Passat already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating tires for Subaru Outback already 50 brands participate!
For cabin filter Fram already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
