I got PMu Street Comp pads and rotors on mine, about a couple weeks ago. They are solid, definitely highly recommend the brand.
Wagner, Centric, Raybestos, Akebono are all very reliable brands. However, each one makes an economy, OEM and premium version. So don't go by brand name alone. Wagner OEX pads are premium quality. They're built on galvanized steel backing plates with mechanical attachment versus adhesive to keep the friction material on.
I put Wagner on mine. They have been good for around 35k miles on them so far. I don't see me replacing them for another 15k. I didn't like the OEM one and braking is really one of the weakspoints for the Mazda 6.
I highly recommend Wagner OEX pads. Galvanized steel backing plates. Quiet. Long lasting
The street type are great all rounders, reasonable bite and minimal drop off. Pretty low dust and noise, and wear was terrific. The set I had lasted longer than the oem pads I had before them. The performance of the track orientated pads is absolutely insane. The initial bite is like no other pad I've ever had. It drops off a tad but still great stopping power. However dust and noise are pretty terrible.
I run the Project Mu HC+ and DBA4000 rotors on a FK8 CTR that is also daily driven. over all very happy works ok when cold but 1 or 2 stops and its up to temp and has great bite. and really only minor pad sequel when stone cold.
I purchased Durango rotors and Wagner brakes for my 2015 cx5 back in May 2018. According to my buddy my brakes were only 50%/35%(front/back/) done. I told him to change it anyways since he pulled them apart anyways. That was around 105k. Around Jan 2020, the rear brakes were squeaking. My buddy pulled them apart, and the rear brakes were completely done. The odometer was around 190k . I replaced them with centric rotors and power stop pads. The front was not changed as it looks like 70 left.
I’ve honestly never had a problem with Wagner. Just installed QuickStops on my wife’s Altima. They are quiet, and they bite just as hard as OEMs.
The best solution I have found is to use slotted rotors--cryo treatment typically gets me 10K more miles before hard spots develop and I get a pedal vibration--and an aggressive pad without any ceramics. My solution is to use the best quality slotted rotor I can find, cryo treatment preferred, and use either a Wilwood BP-10/20 pad or a Project Mu NS brake pad. I found those two pads were aggressive enough to have great stopping power and would wear out the rotor at the same rate the pad wore down.
Ok, so, at a particular location I worked at we used Wagner Thermoquiets. Decent pads, but this particular location seemed to get the worst quality pads ever. The only way we could keep the customer from coming back was to make sure everything was well lubricated, and we also used some sort of orange goop to stick the brake pads to the calipers. Then we took it out for a break-in session, I believe it was 5 stops from 30mph, gently using the brakes, then another 5 with moderate brake pressure. And if the customer was too hard on the brakes it might still come back.
Write your review
Help others - share your experience with this part.
Voted AGAINST engine oil RAVENOL on the rating page
The brake pads OEM Alfa Romeo got the first review!
The brake caliper OEM BMW got the first review!
The brake pads OEM Infiniti got the first review!
For wiper blades PIAA already 100 reviews.
For battery Energizer already 25 reviews.
In the rating best water pump already 12 brands participate!
In the rating best timing belt already 13 brands participate!
In the rating best head gasket already 3 brands participate!
In the auto rating oil filter for Volkswagen Passat already 5 brands participate!
In the auto rating brake pads for Mazda 5 already 10 brands participate!
In the auto rating tires for Subaru Outback already 50 brands participate!
For cabin filter Fram already 25 reviews.
Voted AGAINST engine oil RED LINE on the rating page
Voted AGAINST engine oil PENNZOIL on the rating page
