Brake discs Brembo or ATE

It was my understanding porsche rotors are forged as one piece with holes already in them, not drilled post facto. nothing either way, i have brembos so im bias. but i will say the cadium plating is nice in keeping rust and what's nots away. bonus, only $125 for the pair when i got them; 11\" rotors, Xdrilled/slotted. as for pedal fade, by SS lines and kiss it goooodddbyeeeeeee

In general, race cars will use flat (not drilled, not slotted) rotors if possible, or if restricted by the rules. If restrictions on wheel or rotor sizes are such that it's not possible to get fade free braking without resorting to slots or cross drilling, then slotted (or cross drilled) rotors are used as a last resort to reduce fade. For example, in SCCA club racing, for the improved touring category, drilled or slotted rotors are prohibited. Only stock replacement rotors (stock diameter, stock thickness and configuration) are allowed. Where materials and pads are unrestricted, even though size might be restricted, teams tend to go without drilling or slotting if they can get the brakes to operate fade free with flat rotors. Most Formula one teams today use 275mm (10.9\") flat surface rotors (ventilated, two plate rotors with vents between the plates, but no crossdrilling or slotting). I'm not sure if the rotors are limited to that size by the regs, or if that's the largest rotor that fits within the required wheels, but that's what they run. Since they can run full carbon rotors and carbon pads, there's no fade issues and there's no reason to slot or drill the rotors. Actually, slots or cross drilling would wear the pads quicker and would be a disadvantage for them. In Nextel Cup (formerly Winston Cup), there is a maximum wheel diameter of 15\" and wheels must be steel (alloy wheels are prohibited). Those cars weigh 3400 pounds, too, and the air flow to the brakes with the steel wheels is poor. Those teams tend to run slotted rotors, though they change rotors for every race weekend (some teams change rotors several times during practice and qualifying and start the race on another new set of rotors). They aren't too concerned with fatigue life issues and brake pad wear issues on their brakes. If the pads wear too quickly, they start the race with thicker pads. In sports car racing, ALMS prototypes generally try to run big enough rotors and wheels so they can avoid drilled or slotted rotors. On the long endurance races, the added pad wear from drilled or slotted rotors is significant and can require additional long pit stops to change brake pads more frequently. If you can get the brakes working fade free without slotted rotors, you'll have the advantage of fewer brake pad change pit stops. So most teams try to run rotors with flat surfaces in the long endurance races. For sprint races, they might go to slotted rotors at tracks that are particularly hard on brakes because they might have fade issues that the slots help resolve. For the GT classes in ALMS, the cars are heavier and the thermal loads on the brakes are higher, so they are more likely to use slotted rotors. I don't think many teams use drilled rotors any more. Drilled rotors have serious cracking problems and slotted rotors are much less likely to crack. But even when race teams use slotted or drilled rotors, they use only well engineered slotted rotors when they go to slotted rotors, or very well engineered drilled rotors if they use drilled rotors. There are a few well engineered slotted rotors (ATE Power Discs come to mind) that are sold through retail channels. And most of the Brembo and some of the Zimmerman cross drilled rotors that are availbe through retail sources are very well engineered, too. Most of the rest of the \"tuner\" sourced cross drilled and/or slotted rotors are not as well engineered. And these can cause very serious problems due to design compromises. The \"custom made\" rotors that are made this way are often purely decorative, and to someone who knows the engineering principles behind drilled or slotted rotors, they just look stupid. So, for your VW, you'd be better off running better pads (higher cF, higher operating temperature range) on stock rotors. If you're already running the highest performance pad that's feasible and you are still having issues with fade due to racing or aggressive track driving or very aggressive canyon runs, then slotted rotors might be something to consider. Bigger brakes might be something to consider as well. But you can go way, way better than Mintex Red Box and get much, much better performance on stock rotors, without going to slots or cross drilling.

I found another set of rotors offered by Futrell and i think i'm gonna be goin with these ones They are brembo cross-dimpled/slotted rotors only $140 for a pair of 9.4\" and i think i'll use Mintex Red-Box pads with these thanks for all the feedback

I upraded from mintex red pads and stock rotors to hawk hps pads and brembo cross drilled and slotted rotors and what a world of difference.

I have Ate rotors and Mintex Redbox on my Golf 2.0 and it stops well...no brake dust and the bite is much better than stock pads although it could still use a lot of improvement though.

Brembo's latest big brake kit with 1-piece rotor comes with powerful 4 piston calipers, carriers, stainless braided brake lines, option of race or street pads, and 13" Brembo race rotors! Calipers colors are available in black, red or silver. These rotors have directional veins and are either available in cross-drilled or slotted options. The 13" 1-piece rotor can absorb and dissipate much more heat without warping than most 2-piece rotors. Using Goodridge DOT approved brake lines for solid pedal feel you have your choice of pads for street, autocross, or race at no extra charge. Believe it or not the Brembo 1-piece kit is still lighter than the factory brakes!

i run brembo crossdrilled and slotted rotors mon mintex pads... VERY happy. never experianced brake fade and if u ever drive with me ull know i like to hit the brakes HARD.

ATE powerslots are plated, they dont really rust. the braking surface will eventually, when the plating wears, but the reas of it lasts a long time. I like mine.

How much did those Brembo's set you back ?

i don't think there worth it. just get some brembos.